Choke Control Set - BMW Airhead Post 1980 Cafe Racer; 13 23 1 260 191 / EnDuraLast
Choke Control Set - BMW Airhead Post 1980 Cafe Racer; 13 23 1 260 191 / EnDuraLast
  • Load image into Gallery viewer, Choke Control Set - BMW Airhead Post 1980 Cafe Racer; 13 23 1 260 191 / EnDuraLast
  • Load image into Gallery viewer, Choke Control Set - BMW Airhead Post 1980 Cafe Racer; 13 23 1 260 191 / EnDuraLast

Choke Control Set - BMW Airhead Post 1980 Cafe Racer; 13 23 1 260 191 / EnDuraLast

Regular price
$63.25 USD
Sale price
$63.25 USD
Regular price
Sold out
Unit price
per 
Shipping calculated at checkout.

Choke Control Assembly for Bing CV and Slide carburetors - stainless steel and includes installation instructions.
NOTE: The "choke pull" enables you to remove the stock cables and lever assembly. See ChokePull340 for the pre-1980 choke pull.

Vehicle Manufacturer: BMW Application: Make/Model: Model Years: 1980 Manufacturer #: 13 23 1 260 191 (See APPLICATION TABLE tab BELOW to verify vehicle fitment)


Choke Pull Installation

1. Remove the standard control lever on the air filter box and remove the two choke cables.

2. Replace the levers on the carburetors with the supplied levers. The new levers look identical but are slightly longer. Fit the cable/lever fasteners that were on the old levers onto the new levers.

3. Leave the cable adjusters in place on the carburetors.

4. Set the adjusters to roughly 3mm from being fully screwed down and tighten the lock nuts.

5. Screw the choke pull adjuster with the white plastic bush into the top of the choke adjusters.

6. Lightly grease the new plunger wires to aid installation. Pass the plunger wires through the white bush and it’s adjuster and through the hole in the choke pull fastener in the same way it was done with the original cable. Ensure that the lever on the carburetor is in its filly down position and that the plunger is raised 2mm above the top of the adjuster. Tighten the choke pull so that the cable is clamped to the lever.

7. Repeat step 6 for the other carburetor.

8. Install the black plastic cover where the choke levers were located using the shorter screw and the original nut and the installation is now complete.

EME Part Number: ChokePull339
Model Year
R45 (248) 09/80-07/85 ECE
R45/N (248) 09/80-07/85 ECE
R45T (248) 10/80-06/85 ECE
R45T/N (248) 09/80-07/85 ECE
R60 TIC (2477) 09/80-11/82 ECE
R65 (248) 09/80-07/85 ECE
R65 (248) 09/80-04/85 USA
R65LS (248) 03/81-03/85 ECE
R65LS (248) 06/81-02/85 USA
R65T (248) 09/80-07/85 ECE
R80 (2477) 09/80-11/84 ECE
R80TIC (2477) 09/80-01/85 ECE
R100/7T (2474) 09/80-10/84 ECE
R100/T (2474) 09/80-09/84 USA
R100RS (2474) 09/80-11/84 ECE
R100RS 77-84 (2474) 09/80-10/84 USA
R100RT (2474) 09/80-10/84 ECE
R100RT 79-84 (2474) 09/80-09/84 USA

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)